DIMMING AND OCCUPANCY SENSORS

SPEC
150° Dual-Technology PIR/Ultrasonic Low Voltage Occupancy Sensor
MDW-L SERIES
This Dual Technology Occupancy Sensor combines advanced passive infrared (PIR) and ultrasonic technologies into one unit. Thecombined technologies help to avoid false triggering even in difficult applications. The MDW-L turns lighting on and off based on occupancy and ambient light levels.
The sensor offers numerous operating modes that can be combined to create the ideal custom control. Selectable operating mode allow the sensor to turn a load on, and hold it on as long as either or both technologies detect occupancy. After no movement is detected for the selected time delay, the lights switch off. A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30 seconds following an occupancy detection. This sensor contains a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the area is occupied.
* The MDC-50L operated on 24V supplied by MPP-24 power pack
SPECIFICATIONS
PRODUCT SERIES
MDW-V
VOLTAGE
18-28VDC/VAC
CURRENT CONSUMPTION
40mA
ADJUSTMENT TIME DELAY
5 Sec. to 30 Min.
TEST MODE
Delay time is 5 sec. lasts to 30 min. at each time by setting
PIR ADJUSTMENT
50% OR 100%
(DIP switch 1)
ULTRASONIC ADJUSTMENT
Minimum to maximum (trimpot 1)
LIGHT LEVEL ADJUSTMENT
100 LUX - Daylight (trimpot 2)
PIR COVERAGE
1000 FT2
ULTRASONIC COVERAGE
800 FT2
POWER SUPPLY
MPP-24 Power Pack
OPERATING TEMPERATURE
32° TO 131° F (0° TO 55° C)
FINISH
White

SPEC
150° Dual-Technology PIR/Ultrasonic Line Voltage Occupancy Sensor
MDW-V SERIES
This Dual Technology Occupancy Sensor combines advanced passive infrared (PIR) and ultrasonic technologies into one unit. The combined technologies help to avoid false triggering even in difficult applications. The MDW-V turns lighting on and off based on occupancy and ambient light levels.
The sensor offers numerous operating modes that can be combined to create the ideal custom control. Selectable operating mode allow the sensor to turn a load on, and hold it on as long as either or both technologies detect occupancy. After no movement is detected for the selected time delay, the lights switch off. A “walk-through” mode can turn lights off after only 3 minutes, if no activity is detected after 30 seconds following an occupancy detection. This sensor contains a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the area is occupied.
SPECIFICATIONS
PRODUCT SERIES
MDW-V
VOLTAGE
120/277 VAC @50/60Hz
CURRENT CONSUMPTION
8A. Controls Incandescent, CFL, and LED Lighting
ADJUSTMENT TIME DELAY
5 Sec. to 30 Min.
ULTRASONIC ADJUSTMENT
Minimum to maximum (trimpot 1)
LIGHT LEVEL ADJUSTMENT
100 LUX - Daylight (trimpot 2)
PIR COVERAGE
1000 FT2
ULTRASONIC COVERAGE
800 FT2
TEST MODE
Delay time is 5 sec. lasts to 30 min. at each time by setting
PIR ADJUSTMENT
50% OR 100% (DIP switch 1)
FINISH
White

SPEC
360° Dual-Technology PIR/Ultrasonic Line Voltage Occupancy Sensor
MDC-50V SERIES
The MDC-50V 360° Dual-Technology Occupancy Sensor combines advanced passive infrared (PIR) and ultrasonic technology into one unit. The combined technologies help to avoid false triggering. Selectable operation modes allow the sensor to turn back on and hold it on as long as either or both technologies detect occupancy. After no movement is detected for the selected time delay, the lights switch off.
SPECIFICATIONS
PRODUCT SERIES
MDC-50V
INCANDESCENT
800W-120VAC, 50/60Hz
FLUORESCENT
800VA-120VAC, 1600VA-277VAC, 50/60Hz
ULTRASONIC ADJUSTMENT
Minimum to maximum (trimpot 1)
LIGHT LEVEL ADJUSTMENT
100 LUX - Daylight (trimpot 2)
PIR COVERAGE
1600 FT2
ADJUSTMENT TIME DELAY
5 Sec. to 30 Min.
TEST MODE
Delay time is 5 sec. lasts to 30 min. at each time by setting
PIR ADJUSTMENT
50% OR 100% (DIP switch 1)
ULTRASONIC COVERAGE
1000 FT2
MOTOR
1/4HP-120VAC, 50/60Hz
FINISH
White

360° Dual-Technology PIR/Ultrasonic Low Voltage Occupancy Sensor
MDC-50L SERIES
The MDC-50L 360° Dual-Technology Occupancy Sensor combines advanced passive infrared (PIR) and ultrasonic technology into one unit. The combined technologies help to avoid false triggering. Selectable operation modes allow the sensor to turn back on and hold it on as long as either or both technologies detect occupancy. After no movement is detected for the selected time delay, the lights switch off. * The MDC-50L operated on 24V supplied by MMP-24 power pack (sold separately).
SPEC
SPECIFICATIONS
PRODUCT SERIES
MDC-50L
VOLTAGE
24VDC
LIGHT LEVEL ADJUSTMENT
100 LUX - Daylight (trimpot 2)
PIR COVERAGE
1200 FT2
POWER SUPPLY
MPP-24 Power Pack
ADJUSTMENT TIME DELAY
5 Sec. to 30 Min.
TEST MODE
Delay time is 5 sec. lasts to 30 min. at each time by setting
50% OR 100% (DIP switch 1)
PIR ADJUSTMENT
ULTRASONIC ADJUSTMENT
Minimum to maximum (trimpot 1)
ULTRASONIC COVERAGE
1000 FT2
OPERATING TEMPERATURE
32° to 131° F (0° to 55° C)
STANDARDS AND CERTIFICATIONS
UL Listed
WARRANTY
2 years
FINISH
White

SPEC
Commercial Grade Occupancy/Vacancy Sensor with 0-10V Dimmer Switch
DWODS-010 SERIES
The Enerlites 0-10V passive infrared sensor and dimming switch works by detecting the difference between heat emitted from the human body in motion and the background space. The sensor switch can turn a load on and hold it as long as the sensor detects occupancy. After no motion is detected for the set time delay, the load turns off automatically. This product has one relay (equal to a Single Pole Switch).
SPECIFICATIONS
PRODUCT SERIES
DWODS-010
LOAD RATING
Up to 30mA
IEC 60929 BALLAST/DRIVERS CURRENT DRAW
2mA Maximum
TIME DELAY
15 sec. to 30 mins.
MOTOR
1/8 HP
LIGHT LEVEL
30 Lux - Daylight
OPERATION TEMPERATURE
32° F - 104° F
VOLTAGE
120-277VAC, 60 Hz
FINISH
White

SPEC
In-Wall Occupancy/Vacancy Sensor
MWOS SERIES
This Multi-Technology Wall Switch Sensor combines advanced passive infrared (PIR) and ultrasonic technologies into one unit. The combined technologies help eliminate false triggering even in difficult applications. Selectable operating modes allow the sensor to turn a load on, and hold it on as long as either or both technologies detect occupancy. After no movement is detected for the selected time delay, the lights switch off. A "walk-through" mode can turn lights off after only 3 minutes if no activity is detected after 30 seconds following an occupancy detection.
This sensor also contains a light level sensor. If adequate daylight is present, the sensor holds the load OFF until light levels drop, even if the area is occupied.
SPECIFICATIONS
PRODUCT SERIES
MWOS
VOLTAGE
120/277VAC, 50/60Hz
INCANDESCENT
800W-120VAC, 50,60Hz
FLUORESCENT
800VA-120VAC, 1600VA-277VAC, 50/60Hz
RESISTIVE
800W-120VAC, 50/60Hz
MOTOR
1/4 HP-120VAC, 50/60Hz
ADJUSTMENT TIME DELAY
5 sec. to 30 min.
WALK-THROUGH MODE
3 min. if no activity after 30 min.
TEST MODE
5 sec. at initial power up or DIP switch reset.
PIR ADJUSTMENT
High or Low (DIP Switch)
ULTRASONIC ADJUSTMENT
Minimum to Maximum (trimpot)
LIGHT LEVEL ADJUSTMENT
100 Lux - Daylight (trimpot)
OPERATION TEMPERATURE
32° F - 131° F
FINISH
White

SPEC
POWER PACK
MPP-24 SERIES
The MPP-24 power pack is the foundation for any low voltage lighting control system. The MPP-24 supplies low voltage power to occupancy sensors and other control devices, switching line voltage in response to signals from control devices. The MPP-24 power pack is attached to existing junction boxes or mounted into fixture wiring trays. Low voltage wiring should use at least 22-gauge wire. High voltage connections should use at least 14- gauge. Always check local building codes. After initial wiring is completed, check wiring diagrams to verify the power pack is wired correctly. Improper wiring can cause damage to the power pack, lighting system, occupancy sensor and other control devices.
SPECIFICATIONS
PRODUCT SERIES
MPP-24
VOLTAGE
120/277VAC, 50/60Hz
BALLAST
20A @ 120/277VAC
INCANDESCENT
20A @ 120VAC
MOTOR
1HP @120/240VAC
CONTROL ON
12-24VDC
HOLD ON
12-24VDC
HOLD OFF
12-24VDC
MANUAL ON (MOMENTARY SWITCH REQUIRED)
12-24VDC
OUTPUT
150mA @24VDC (with relay connected)
OPERATING TEMPERATURE
32° F - 131° F
RELATIVE HUMIDITY
20-90%, Non-condensing
WARRANTY
2 Years
MATERIAL
ABS

Dimmable LED/CFL 0-10V Dimmer Single Pole/Three-way
DMD-LED3-105 SERIES
The DMD-LED3-105 is a 0-10V decorator dimmer switch that provides optimal dimming control for 0-
10V compatible LED drivers, fluorescent ballast and HID ballast. The DMD-LED3-105 dimmer features a mini paddle switch to turn your lights off or on and returning them to your desired level at any time.
SPEC
KEY FEATURES
-
Convenient operation combines ON/OFF Decorator mini switch with separate slider for dimming control.
-
Low voltage pigtails are labeled separately.
-
Switch 120-277 VAC.
-
Dimming control 10V.
-
Provide a wide range of dimming, lighting fades up and down smoothly.
-
Adjustable high-end and low-end trim for optimal dimming performance.
-
Designed for compatibility with most high efficacy light bulbs.
-
Constant memory returns lights to the previous level after a power failure.
-
Proper color matching.